Learn About Exchange Server 20071 | 2 | 3 |
A. The Receive connector on the Edge Transport server.
B. The Receive connector on the Hub Transport server.
C. The Send connector from the Edge Transport server to the Internet.
D. The Send connector from the Hub Transport server to the Edge Transport server.
E. The Send connector from the Edge Transport server to the Hub Transport server.
You should reconfigure the Send connector from the Edge Transport server to the Internet. The connector is created by default when you subscribe an Edge Transport server to Active Directory. However, this connector is configured by default to communicate with any SMTP server on the Internet, so you should reconfigure it to communicate only with the smart host at your ISP. You configure a send connector using the Set-SendConnector cmdlet.
You do not need to reconfigure the Receive connector on the Edge Transport server. When you install the Edge Transport role on a server, a Receive connector is created by default. It is configured to receive mail from any source, both from the Internet and from the Hub Transport servers in your organization.
You do not need to reconfigure the Receive connector on the Hub Transport server. This connector is created by default when you install the Hub Transport role, and it is configured to receive mail from addresses internal to your network.
You do not need to reconfigure the Send connector from the Hub Transport server to the Edge Transport server. This connector is created by default with the correct settings on each Hub Transport server in the site to which you subscribe the Edge Transport server.
You do not need to reconfigure the Send connector from the Edge Transport server to the Hub Transport server. This connector is created and configured correctly when you subscribe an Edge Transport server to Active Directory.
Configuring Edge Transport Server Connectors
How to Configure Connectors for Internet Mail Flow
Lesson 1: Introduction to Message Transport, Course 5047A
Module 7: Managing Message Transport
Subscribing the Edge Transport Server to the Exchange Organization
Multiple answer, multiple-choice
You are planning to add an Exchange 2007 server to an existing organization. The organization has the Exchange servers shown in the exhibit. The organization resides in an Active Directory domain, running at the Windows 2000 native functional level. What changes must you make to the network before adding the Exchange 2007 server to the organization? (Each correct answer presents part of the solution. Choose two.)
A. Convert the Exchange organization to native mode.
B. Raise the domain functional level to Windows Server 2003.
C. Upgrade the operating system to Windows Server 2003 on EXCH1, EXCH2 and EXCH3.
D. Decommission EXCH3.
E. Decommission EXCH2.
You must decommission or upgrade EXCH2 and convert the Exchange organization to native mode. Exchange 2007 cannot coexist in the same organization as Exchange 5.5. Also, it must be installed in an Exchange organization running in native mode.
You do not need to raise the domain functional level to Windows Server 2003. The minimum domain functional level required is Windows 2000 native mode. You do not need to upgrade the operating system to Windows Server 2003 on EXCH1, EXCH2 and EXCH3.
Although Exchange 2007 must be installed on computers running Windows Server 2003, other Exchange servers do not have that requirement. Exchange Server 2000 must have at least SP 3 installed and Exchange Server 2003 must have at least SP 2 installed, but those requirements are already met by the configuration.
You do not need to decommission EXCH3. Exchange 2007 can coexist with Exchange Server 2000 as long as SP3 is installed.
Exchange 2007 System Requirements
Lesson 2: Installing Exchange Server 2007
Module 2: Installing Exchange Server 2007
Single answer, multiple-choice
You need to change the path where the Hub Transport server's message logs are stored to a different hard drive. What cmdlet will you use?
You should use the cmdlet:
Set-TransportServer -Identity -MessageTrackingLogPath
The Set-TransportServer cmdlet allows you to modify a number of configuration settings for a transport server, including message tracking options.
You should not use the cmdlet Set-ExchangeServer. The Set-ExchangeServer cmdlet allows you to enable error reporting and identify the domain controllers that should be used for directory service access by the Exchange Server.
You should not use the Set-TransportConfig cmdlet. You use the Set-TransportConfig cmdlet to set organization-wide settings for transport servers. The path to the message log is a server-specific setting.
You should not use the Set-TransportRule setting. You use the Set-TransportRule setting to configure a rule that will be used by a transport server to process a message.
How to Configure Message Tracking
Microsoft Exchange Server 2007 Online Help
Exchange Management Shell
New Administration Functionality in the Exchange Management Shell
Lesson 2: Implementing Message Transport
Module 7: Managing Message Transport